Here I've used two separate power supplies-a 6V powering the NE555 and a 12V powering the 2N3055 and the flyback.I've also used a COSMO 1010 (C1010) photocoupler to make sure that the NE555 doesnt blow from the 12volt supply. The coil The secondary coil has about 400 turns of 0.4mm magnet wire wrapped around a 3cm paper roll.The primary is 5 turns of speaker wire. The spark gap Just two screws not attached to anything facing each other. Capacitor bank Here are the capacitors I've used: 5̶3̶2̶J̶,̶ ̶4̶7̶4̶J̶,̶ ̶.̶2̶7̶J̶ ̶,̶ ̶.̶6̶4̶J̶,̶ ̶.̶2̶2̶J̶,̶ ̶1̶0̶5̶J̶,̶1̶2̶4̶J̶,̶ ̶8̶2̶2̶J̶/̶1̶.̶6̶K̶V̶.̶M̶o̶s̶t̶ ̶o̶f̶ ̶t̶h̶e̶ ̶o̶t̶h̶e̶r̶ ̶c̶a̶p̶s̶ ̶a̶r̶e̶ ̶r̶a̶t̶e̶d̶ ̶4̶0̶0̶V̶o̶l̶t̶s̶ ̶I̶ ̶t̶h̶i̶n̶k̶.̶O̶n̶e̶ ̶o̶r̶ ̶t̶w̶o̶ ̶2̶0̶0̶V̶o̶l̶t̶s̶.̶ S̶o̶ ̶,̶i̶f̶ ̶m̶y̶ ̶c̶a̶l̶c̶u̶l̶a̶t̶i̶o̶n̶s̶ ̶a̶r̶e̶ ̶c̶o̶r̶r̶e̶c̶t̶ ̶t̶h̶e̶n̶ ̶t̶h̶e̶ ̶b̶a̶n̶k̶ ̶s̶h̶o̶u̶l̶d̶ ̶b̶e̶ ̶a̶b̶o̶u̶t̶ ̶4̶K̶V̶o̶l̶t̶s̶ ̶a̶n̶d̶ ̶9̶0̶0̶ ̶p̶F̶s̶.̶. The calculations were wrong -this was too much capacitance.I've replaced this chain of capacitors with a single DIY aluminum foil and plastic sheets as dielectric capacitor.I am not aware of the capacitance value of this though.I do not own an LC meter. Here is how I made this homebrew capacitor. Om namo venkatesaya om namo srinivasa song download.

Tesla Coil Tuesday - Building a Full Bridge SSTC part 2 - Gate drive Transformers. Issues of: gate charge. These are a whole bunch of things to make with the 555 timer IC with a note for each picture. I do not take credit for these schematics, they were made by Collin.

Crack license dat matlab simulink examples for kids. Maybe the bank is not good enough for spark on top.Maybe the bank is the culprit. How to get the constant spark on top? I know it has something to to do with resonance.Obviously there is no resonance here.

Here I've used two separate power supplies-a 6V powering the NE555 and a 12V powering the 2N3055 and the flyback.I've also used a COSMO 1010 (C1010) photocoupler to make sure that the NE555 doesnt blow from the 12volt supply. The coil The secondary coil has about 400 turns of 0.4mm magnet wire wrapped around a 3cm paper roll.The primary is 5 turns of speaker wire. The spark gap Just two screws not attached to anything facing each other. Capacitor bank Here are the capacitors I've used: 5̶3̶2̶J̶,̶ ̶4̶7̶4̶J̶,̶ ̶.̶2̶7̶J̶ ̶,̶ ̶.̶6̶4̶J̶,̶ ̶.̶2̶2̶J̶,̶ ̶1̶0̶5̶J̶,̶1̶2̶4̶J̶,̶ ̶8̶2̶2̶J̶/̶1̶.̶6̶K̶V̶.̶M̶o̶s̶t̶ ̶o̶f̶ ̶t̶h̶e̶ ̶o̶t̶h̶e̶r̶ ̶c̶a̶p̶s̶ ̶a̶r̶e̶ ̶r̶a̶t̶e̶d̶ ̶4̶0̶0̶V̶o̶l̶t̶s̶ ̶I̶ ̶t̶h̶i̶n̶k̶.̶O̶n̶e̶ ̶o̶r̶ ̶t̶w̶o̶ ̶2̶0̶0̶V̶o̶l̶t̶s̶.̶ S̶o̶ ̶,̶i̶f̶ ̶m̶y̶ ̶c̶a̶l̶c̶u̶l̶a̶t̶i̶o̶n̶s̶ ̶a̶r̶e̶ ̶c̶o̶r̶r̶e̶c̶t̶ ̶t̶h̶e̶n̶ ̶t̶h̶e̶ ̶b̶a̶n̶k̶ ̶s̶h̶o̶u̶l̶d̶ ̶b̶e̶ ̶a̶b̶o̶u̶t̶ ̶4̶K̶V̶o̶l̶t̶s̶ ̶a̶n̶d̶ ̶9̶0̶0̶ ̶p̶F̶s̶.̶. The calculations were wrong -this was too much capacitance.I've replaced this chain of capacitors with a single DIY aluminum foil and plastic sheets as dielectric capacitor.I am not aware of the capacitance value of this though.I do not own an LC meter. Here is how I made this homebrew capacitor.

Maybe the bank is not good enough for spark on top.Maybe the bank is the culprit. How to get the constant spark on top? I know it has something to to do with resonance.Obviously there is no resonance here.